Client Connection: PESIT
Fields with the asterisk * are mandatory.
NAME *
Name of the PESIT connection you are creating. The maximum number of characters is 128. Blanks and these special characters: ' " | are not supported.
DESCRIPTION
Description of the PESIT connection you are creating. The maximum number of characters is 2048.
STATUS
Enable or disable the client connection. Possible values:
Enabled (default value)
Disabled
HOST *
Remote host IP Address or hostname.
PORT *
Port to connect to the remote host (1 to 65535).
USERNAME *
Username to be used for the connection. The maximum number of characters is 320.
PASSWORD
User password.
CONNECT THROUGH DMZ
Enable or disable DMZ proxy. Possible values:
Enabled
Disabled (default value)
PESIT REMOTE NODE IDENTIFIER
Remote identifier of PESIT. Logical identifier that is submitted to Data One. If an ID different from the ID contained in this field is submitted, the connection fails. The maximum number of characters is 24. Blanks are not supported. Special characters allowed: - _ .
PESIT LOCAL NODE IDENTIFIER
Local Identifier of PESIT. Logical identifier that Data One submits to connect. If an ID different from the ID contained in this field is submitted, the connection fails. The maximum number of characters is 24. Blanks are not supported. Special characters allowed: - _ .
INTERVAL BETWEEN SYNC POINTS
Number of synchronization points in Kb used to restart a transfer after an incident. Default number: 1024. The value of this field must always be greater or equal to 4.
ACKNOWLEDGEMENT WINDOW SIZE
Acknowledgement window size. This is the number of synchronization points without answer that can be sent before the transfer is stopped. Default number: 3.
MAX RETRIES
Maximum number of retries. If this field is empty or set to 0, no retries will be executed and the job will be set to Failed if the first attempt is not successful. A high value corresponds to a high number of retrying attempts.
RETRY INTERVAL
This field will appear only if you have set the maximum numbers of retries to 1 or greater. Time (in seconds) waited before retrying executing a job. The lower the value, the more frequent the retrying attempts. If this field is empty or set to 0, no retries will be executed and the job will be set to Failed if the first attempt is not successful.
PESIT Protocol Configuration
To set up a PeSIT configuration, define the following entities:
a VFS
a Remote Actor with a User
a remote connection to a Remote PeSIT node
a Server template with PeSIT protocol
In the Actors section, click the New button and create Partner PXFB01. Click the New User button and create User USR99:
Go to the VFS tab and click the NEW button to define a VFS for Partner PXFB01:
Go to Setup → STENG, Clusters & Servers and define a new PeSIT remote Server to connect to/be connected from. Click the NEW SERVER button and define connection parameters to the remote PeSIT Node XFB01:
PROTOCOL TYPE
PeSIT
SERVER NAME
PXFB01_PROTOCOL
DESCRIPTION
Remote Access Config Pesit x XFB01
ENABLED
Yes
DMZ PROXY ENABLED
No
REMOTE HOST
IP of the remote Host
REMOTE PORT
Port of remote Host
USERNAME
Username to establish the connection
REMOTE ID
XFB-01
LOCAL ID
SPENTC12
Do not set a password to connect to the XFB-01 remote PeSIT node. The parameters not mentioned can be omitted.
Now define the PeSIT Server Template, with the following parameters:
Server configuration:
PROTOCOL TYPE
PeSIT
TEMPLATE NAME
PESIT01
DESCRIPTION
PeSIT local server
ENABLED
Yes
DEFAULT LISTENING PORT
51600
DIAGNOSTIC PORT 1
51601
DIAGNOSTIC PORT 2
51602
MAXIMUM PDU SIZE
30000
The PESIT server is now installed in the STENG folder. Note that if the path of this folder is longer than 52 characters, the PESIT server cannot be run, and an error appears in the
messages.log.
To solve this issue, you must create a Symbolic Link (SymLink) and edit the server.env file as shown in the example here below:
Steng folder = /home/user1/installation/ghibli-home/wlp/usr/servers/steng
Information available in the server.env installation file:
KEYMXMS=PRIMPESI-AA7BB8O483
OSIVERS=3.6B.01
OSIROOT=/home/user1/installation/ghibli-home/wlp/usr/servers/steng/pesit/SPRun/pesit
Create the SymLink:
Go toln -s /home/user1/installation/ghibli-home/wlp/usr/servers/steng /home/user1/PesitDeploy
and modify the server.env file:
KEYMXMS=PRIMPESI-AA7BB8O483
OSIVERS=3.6B.01
PESIT_DEPLOY_DIR==/home/user1/PesitDeploy
OSIROOT=/home/user1/PesitDeploy/pesit/SPRun/pesit
Incoming call:
NAME
Ic_pesit01
DESCRIPTION
Incoming call x XFB-01
INCOMING ADDRESS
0.0.0.0
ACTOR
PXFB01
Allocate the Server Template to a cluster.
Use 0.0.0.0 as IP for local PeSIT to expose the right listening server port
The configuration is now completed.
Last updated
